#Ds lite gameboy macro youtube how to
#Ds lite gameboy macro youtube install
#Ds lite gameboy macro youtube mod
#Ds lite gameboy macro youtube full
#Ds lite gameboy macro youtube tv

This is usefull for playing some DS games on a Gameboy Macro. When i turn on the Ds it seems like the first screen (please touch the tactil screen or press any button.) to pass righ away, with no input given. 1 This will let you switch what screen is displayed on the bottom screen of a phat DS. BUT!Īs you can see in the link below (youtube video: ), EVERY BUTTON works, but 'A'. So, i repaired the F2 fuse, ds lite turn on and everything. When i was trying to go further with my mod, doing the soldering to every button (every pinout point), i was trying to turn it on, and, for error, i blown the F2 fuse (i tried to make de A button works with a side of the resistance, ds lite powered on). Then i red that i supposed to use a 1KOhm resistance, thing that actually worked for me. Well, i tried it and it didnt work for me. I red everywhere that it could be done using a Led light.

#Ds lite gameboy macro youtube how to

I'm from Chile, and for almost a year i was learning how to make the gameboy macro mod.

They can be downloaded from the link below.HELP WANTED, post gameboy macro 'A' button problemĬonsole Modding- ( Here you can talk about your favorite Consoles ) > DS Lite But not one that uses an expensive metal faceplate.

#Ds lite gameboy macro youtube install

They also let you install a Nintendo switch front facing speaker. In today’s episode of Retro Renew, we’re going to make another Gameboy Macro. Ive designed one with 1 button and another with 3 buttons. You might want to 3d print a new faceplate to finish off this build. Below is how I mount my 3 buttons, I connect the top pins together then connect them to the GND On the charge port (any of the 4 corners will do). The P11 and P12 will let you have picture in picture mode and also to change the opaqueness of the mode. This is great for picking which screen you want on the tv. You will want to solder at least one switch to the test points, P10 will let you switch between the top and bottom screen. Last be not least we need to remove a resistor from the other side of the board otherwise we will get interference on the video signal

You just need to solder the 1 – 5 test points to the corresponding resistors in the above schematic.Īlso on the left hand side of the board by where the WIFI card is you will need to wire up the resistors to these 2 points as shown in the schematic above. I found that if you snip the shield off the bottom of the WIFI card it will give you loads of space to fit the resistors under there. So what you want to do is run wires from these test points under the ds slot so they reach just under the WIFI board, That’s where the resistors are going to fit. I use 0.25mm/30AWG solid core enamel wire because its super thin and easy to work with.

#Ds lite gameboy macro youtube mod

When done correctly, the Macro mod is among the cheapest of custom gameboys: all you need is a donor DS Lite and a resistor, both of which are readily available, and to boot its backlit and rechargable right out of the box. Now you have the resistors soldered we can move on to the other solder points. Theres more than one kind of Macro but the most common (and for this build) is a DS Lite. I found that if you lay out your smd resistors on the sticky side of the kapton tape it will hold it all together while you solders them.

Below is the schematic for how they need to be soldered together. I used 1206 smd resistors because they are small and relatively easy to solder together in this configuration, You can use through hole resistors but it will end up being rather bulky and you might not get it to fit into the shell. Once you have your DS Lite flashed we can start soldering the resistors together.

#Ds lite gameboy macro youtube tv

The first thing your going to need to do is flash the TV out firmware to your DS Lite, I’ve written a blog post on how to flash your DS Lite with the TV out firmware HERE so head over to there and come back when your done.

3.5mm headphone jack to white + red RCA jacks.

This makes it a nice sleek mod that uses a 3.5mm male to RCA female cable, you will only have mono sound out to the TV. Join me below to see how its done.įor this mod I’m going to be wiring the TV out to come out of the headphone jack. The Neon Advance is basically a Game Boy Macro a modified Nintendo DS Lite that is meant to play Game Boy Advance Games. I must warn you that this isn’t an easy mod to pull off and requires micro soldering.

#Ds lite gameboy macro youtube full

I found out about away to do the TV out with only a hand full of resistors which blew my mind. game boy advance macro by tintxu, reciclamos una nintendo ds lite rotaenlace compra amazon resistencias 330ohmios: https. Ive always liked the idea of the TV out mod on the ds lite but one thing has always held me back….The price and availability of parts to build one.